All Parts > Integrated Circuits (ICs) > Interface ICs > Texas-Instruments-SN75970B2DLRG4

Texas Instruments SN75970B2DLRG4

Texas Instruments

Part Number:	Texas Instruments SN75970B2DLRG4
Manufacturer:	Texas Instruments
Part Type:	All Parts > Integrated Circuits (ICs) > Interface ICs > Texas-Instruments-SN75970B2DLRG4
Qty Available:
Description:	SCSI Termination and Transceivers SCSI Differential Converter Control

Get Quote

05/01/2026 – There are 515 pieces pieces of Part Number Texas Instruments SN75970B2DLRG4 Available.

PCX has Texas Instruments All Parts > Integrated Circuits (ICs) > Interface ICs > Texas-Instruments-SN75970B2DLRG4 Electronic Components for Sale.

Pacific Component Xchange specializes in solving challenges such as supply chain procurement, hard to find, long lead time, obsolete, cost savings, kanban and scheduled orders.

SCSI Termination and Transceivers SCSI Differential Converter Control

Alternate Descriptions

Descriptions of Texas Instruments SN75970B2DLRG4 provided by its distributors.
SCSI Termination and Transceivers SCSI Differential Converter Control
Line Transceiver, 9 Func, 9 Driver, 9 Rcvr, PDSO56
IC DIFF CNVRTR CNTRL SCSI 56SSOP
IC TRANSCEIVER HALF 9/9 56SSOP
The SN75970B SCSI differential converter-control, when used in conjunction with one or more of its companion data transceiver(s), provides the superior electrical performance of differential SCSI from a single-ended SCSI bus controller. A 16-bit, Fast-SCSI bus can be implemented with just three devices (two for data and one for control) in the space-efficient, 56-pin, shrink small-outline package (SSOP) as well as the even smaller TSSOP and a few external components. The SN75970B is available in a B2 (20 Mxfer) version and a B1 (10 Mxfer) version. In a typical differential SCSI node, the SCSI controller provides the enables for each external RS-485 transceiver. This could require as many as 27 additional terminals for a 16-bit differential bus controller or relegate a 16-bit single-ended controller to only an 8-bit differential bus. Using the standard nine SCSI control signals, the SN75970B control transceiver decodes the state of the bus and enables the SN75971B data transceiver(s) to transmit the single-ended SCSI input signals differentially to the cable or receive the differential cable signals and drive the single-ended outputs to the controller. The single-ended SCSI bus interface consists of CMOS bidirectional inputs and outputs. The drivers are rated at 16 mA of output current. The receiver inputs are pulled high with approximately 4 mA to eliminate the need for external pullup resistors for the open-drain outputs of most single-ended SCSI controllers. The single-ended side of the device is not intended to drive the SCSI bus directly. The differential SCSI bus interface consists of bipolar bidirectional inputs and outputs that meet or exceed the requirements of EIA-485 and ISO 8482-1982/TIA TR30.2 referenced by the American National Standard of Information Systems (ANSI) X3.131-1994 Small Computer System Interface-2 (SCSI-2) and SCSI-3 Fast-20 Parallel Interface (Fast-20) X3.277:1996. The SN75970B is characterized for operation over the temperature range of 0C to 70C. The SN75970B consists of nine RS-485 differential transceivers, nine TTL- or CMOS-level compatible transceivers, a state machine and control logic block, a 20-MHz crystal-controlled oscillator, a timer, a power-up/-down glitch protection circuit, and a thermal-shutdown protection circuit. The single-ended or controller interface is designated as the A side and the differential port is the B side. Since the device uses the SCSI control signals to decode the state of the bus and data flow direction, the terminal assignments must be matched to the corresponding signal on the SCSI bus. The signal name followed by a a minus sign (-) indicates an active-low signal while a plus sign (+) indicates an active-high signal. A reset function, which disables all outputs and clears internal latches, can be accomplished from two external inputs and two internally generated signals. RESET\ (Reset) and DSENS (differential sense) are available to external circuits for a bus reset or to disable all outputs should a single-ended cable be inadvertently connected to a differential connector. The power-up and thermal-shutdown are internally generated signals that have the same effect when the supply voltage is below 3.5 V or the junction temperature exceeds approximately 175C. This data sheet contains descriptions of the SN75970B input and output signals followed by the electrical characteristics. The parameter measurement information is followed by the theory of operation, a state flow chart, and a typical circuit in the application information section.

Texas Instruments SN75970B2DLRG4

Texas Instruments

Alternate Descriptions

Title

FAQ’s

What is the product name and brand?

What is the function of the SN75970B2DLRG4?

What is the package type and number of pins of the SN75970B2DLRG4?

What is the temperature range for the SN75970B2DLRG4?

Electronic Component Search